Before presenting (proudly presenting… ) my new design, I must give a thanks to every blogger who has shared their designs and ideas on the www. Many thanks!
Not that I don’t want to share my stuff – I didn’t even realize that I had lot’s to share… until I randomly checked my stats the other day and saw people had searched for ‘free intarsia chart for Chicago Bull’ or ‘point of knitted V-neck’ and the like! Oh no, I am so sorry!!! Usually I intend to put details of what I have done up in the post… just as I intend to write up every pattern I knit… and grade it… and make it available in different gauges… but I always run out of time or get stuck into the next project. So, how about you tell me if you want to know something – I’ll reply asap!
And now … ta ta tat taaaaaaa… The Red Rag:
This has taken me some time – not the actual knitting of the Red Rag – allowing myself to finish this (stopping myself from unraveling it over and over, in the search of perfection). The sleeve heads were knitted probably 5 times, the collar at least twice… all new territory for me, a steep learning curve.
Here are the technical bits:
pattern source: Textileshed!
size 38″
yarn: 550gr Bendigo Woollen Mills “Duet” (30% Mohair, 70% Wool), shade 149 “Wildberry”
gauge: 20st/ 26 rows on 3.5mm
method: The body was knitted bottom up, casting on first the entire hem and knitting 6 rows in garter st, then using short rows, I shaped the scalloped hem. The waist and bust are shaped by decreasing/ increasing stitches at the side seam, as well as within the front and back piece. The sleeves are set in, knitted from the top. The front edges and the collar stand are knitted in garter stitch (I had 3 circular needles in operation at the same time to do this, thus I achieved mitered corners where collar stand and front edges converge); the buttonholes on the right front are worked plainly as yo; kn2tog. The collar has got very sharp points – see details below.
Knitty Gritty Bits:
Collar: Here are some close-ups for the collar. I started by knitting a collar stand (6 rows in garter st) as I knitted the front edges. You cannot see the collar stand here in the finished garment at all, but you can see it in the picture with the knitting needles in it.
The collar’s right side is the body’s wrong side, as the collar is folded on itself! The photo above illustrates the existence of the collar stand fairly well, eh? Here are approximate instructions:
- Knit 6 rows in garter st (collar stand) as you knit the front edges
- cast off 3 st of the collar stand (as you cast off the front edges)
- put the next 4 st on hold to be picked up as you knit the edge of the collar in garter st later.
- increase 11 stitches for the collar (after finishing the collar stand), 5 st at the back neck, and 3 st at each front neck in order to make it big enough to fold nicely on itself
- knit 15 rows of garter st, increasing 1st each side – after the first and before the last st (row 3, 7, 11, 15)
- pick up 12 st alongside both short edges of the collar with dp needles and knit 6 rows in garter st along all three edges of the collar. In these 6 rows you need to (1) incorporate the 4 st on each side that were put on hold and (2) work the mitre/ point of the collar.
(1) In rows 2, 3, 5, and in the cast off row one st of the ones on hold are pulled over the first and last st of the row before working that first/ last stitch.
(2) Collar point: chose one st at corner to be knitted in stocking st, to form a clear ‘mitre’, either side of that stitch increase one st in row 1, 2, 3, 5, 6.
Sleeve heads:
knitted from the top down. I picked up as many stitches as were required for the size of the armhole, then decreased enough stitches so I got the amount needed for the top of the sleeve in row 2, knitted row 3 plain and then knitted the sleeve head with short rows. But actually – this is not too bad…
I am not going to give instructions here… since I think there is room for improvement to how I have ended up knitting them on the Red Rag… but this is what I have learned: There are 3 successful ways of knitting fitted sleeves from the top down.
- Pick up stitches around the armhole before you shape the sleeve head with short rows. You have to pick up the amount of st that you will need at the widest part of the sleeve, so think carefully about the sleeve width, the armhole depth and the sleeve head height. (This is an entire blog post…!) This is brilliantly explained on http://www.basixknitting.com/, and may I also add, Sue took the time to give me an incredibly detailed explanation when I contacted her with my queries. Unfortunately, I had knitted the sleeve heads ‘my way’ one time too many… and decided to leave it all. But next time, I will follow her advice to the dot!
- Pick up stitches as you knit your sleeve heads with short rows – personally I would advise against this, unless you clearly mark at what point you pick up the st as you go…
- knit your sleeve heads as you knit your front and back pieces top down… that means you start on your shoulders (front and back), then as you work further down and work your neckline, you also add sts as required to shape the sleeve head – this was ‘invented’/ published by Barbara Walker and I have ordered her book on Amazon – this would be the most sophisticated way ever… and I really want to learn this.
Knitting the hem was an adventure in itself, look at this. As I knitted during Esther’s soccer game, all the mums were wondering why I had knitted the name and date on the inside of the hem… I wonder now myself, this is a great feature to include in a future project (to leave it on the outside!).
textileshed 